AXAGON

Entry:

• 1x USB 3.2 Gen1 / SuperSpeed USB port, USB-A male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• USB connection port with type A (male) connector placed on a 20 cm long cable.

Exit:

• 3x SuperSpeed USB port, USB-A female connector.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.

RJ-45 Output:

• Gigabit Ethernet interface with RJ-45 connector for connection via UTP or STP cable.
• Support 10/100/1000Mbps Ethernet interface baud rate.
• Support specification IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T.
• 10/100/1000 Mbit/s auto-sensing.
• Support IPv4/IPv6 packet Checksum Offload Engine (COE) to lower CPU load including IPv4 IP/TCP/UDP/ICMP/IGMP & IPv6 TCP/UDP/ICMPv6 checksum and checksum generation.
• Support TCP Large Send Offload V1 and V2.
• Support IEEE 802.1P Layer 2 priority encoding & decoding.
• Support IEEE 802.1Q VLAN tagging.
• IEEE 802.3az EEE (Energy Efficient Ethernet) support - reduce idle power consumption.
• Jumbo frame support.
• It supports full duplex transmission with IEEE 802.3x flow control and half duplex transmission with reverse flow control.
• Auto MDI/MDIX support - crossover detection and autocorrection eliminates the need for crossover cables.
• Hardware Cyclic Redundancy Check (CRC) support for detecting transmission errors.
• Support Pair Swap/Polarity/Skew Correction.

Wake-on-LAN support in various modes:

• Support for sleep and remote wake-up with Magic packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection and Link Change wake-up.
• Support of the ECMA-393 proxZzzy for sleeping hosts standard to manage the network connection of sleeping hosts using proxy servers.
• RealWoW technology support! enables remote wake-up via the Internet.

Advanced Power Management features:

The adapter supports advanced power loss management to reduce idle or low network traffic. It also supports advanced power saving when disconnecting from the Ethernet cable.

• Advanced Configuration Power management Interface (ACPI) support.
• Power Management offload (ARP & NS) support.
• Microsoft Always On Always Connected (AOAC) support.
• Intel Converged Platform Power Management (CPPM) support.
• Link Power Management (LPM) support.
• Operating System-directed Power Management (OSPM) support.
• IEEE 802.3az EEE (Energy Efficient Ethernet) support.

Entry:

• 1x USB 3.2 Gen1 / SuperSpeed USB port, USB-A male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• USB connection port with type A (male) connector placed on a 20 cm long cable.

USB output:

• 3x SuperSpeed USB port, USB-A female connector.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.

RJ-45 Output :

• Gigabit Ethernet interface with RJ-45 connector for connection via UTP or STP cable.
• Support 10/100/1000Mbps Ethernet interface baud rate.
• Support specification IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T.
• 10/100/1000 Mbit/s auto-sensing.
• Support IPv4/IPv6 packet Checksum Offload Engine (COE) to lower CPU load including IPv4 IP/TCP/UDP/ICMP/IGMP & IPv6 TCP/UDP/ICMPv6 checksum and checksum generation.
• Support TCP Large Send Offload V1 and V2.
• Support IEEE 802.1P Layer 2 priority encoding & decoding.
• Support IEEE 802.1Q VLAN tagging.
• IEEE 802.3az EEE (Energy Efficient Ethernet) support - reduce idle power consumption.
• Jumbo frame support.

It supports full duplex transmission with IEEE 802.3x flow control and half duplex transmission with reverse flow control.

• Auto MDI/MDIX support - crossover detection and autocorrection eliminates the need for crossover cables.
• Hardware Cyclic Redundancy Check (CRC) support for detecting transmission errors.
• Support Pair Swap/Polarity/Skew Correction.

Wake-on-LAN support in various modes:

• Support for sleep and remote wake-up with Magic packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection and Link Change wake-up.
• Support of the ECMA-393 proxZzzy for sleeping hosts standard to manage the network connection of sleeping hosts using proxy servers.
• RealWoW technology support! enables remote wake-up via the Internet.

Advanced Power Management features:

The adapter supports advanced power loss management to reduce idle or low network traffic. It also supports advanced power saving when disconnecting from the Ethernet cable.

• Advanced Configuration Power management Interface (ACPI) support.
• Power Management offload (ARP & NS) support.
• Microsoft Always On Always Connected (AOAC) support.
• Intel Converged Platform Power Management (CPPM) support.
• Link Power Management (LPM) support.
• Operating System-directed Power Management (OSPM) support.
• IEEE 802.3az EEE (Energy Efficient Ethernet) support.

Entry:

• 1x USB 3.2 Gen1 / SuperSpeed USB port, USB-A male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• USB connection port with type A male connector placed on a 30 cm long cable.

Exit:

• 4x SuperSpeed USB port, USB-A female csatlakozó.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).

Hub power mode via USB cable (bus power):

• USB bus power is sufficient to connect a low-power USB device (mouse, keyboard, card reader, flash drive, etc.) or a self-powered device (printer, scanner, 3.5" external drive) to all four ports.
• In this power mode, the USB hub can also work simultaneously with up to two 2.5" magnetic external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A in each of the hub's ports. Charging (divided into all ports) reaches up to 2.5A at 5V (depending on the capabilities of the computer's USB port).

Hub power mode via USB + external USB charger (self power):

• Integrated micro USB connector for additional power to the hub.
• For additional power supply to the hub, you can use any wall charger for mobile devices (not included) with a micro USB connector (recommended charger output current min. 2A).
• In this power mode, the USB hub can operate up to 3 magnetic 2.5 external drives. This mode is recommended for connecting to smartphones and tablets.
• Charging mobile devices (including iPad) with a current of up to 1.5A in each of the hub's ports. The total charging current (which is divided into ports) reaches up to 4.5A at 5V (depending on the capabilities of the external wall charger).

Entry:

• 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-A male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• USB connection port with type A male connector placed on a 120 cm long cable.

Exit:

• 4x SuperSpeed USB port, USB-A female connector.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.

Properties:

• Possibility to connect the device on the run thanks to Hot Plug support.
• Full Plug and Play support.
• Standby mode support.
• A quality shielded cable guarantees high communication speed and minimal unwanted interference.
• The white LED indicates connection to the computer's USB port.
• Bus powered (USB bus power).

Power / Charging:

• USB power is sufficient to connect low-power USB devices (mouse, keyboard, card reader, flash drive, etc.) or self-powered devices (printer, scanner, 3.5" external drive) to all four ports.
• The USB hub can permanently support several external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A is possible in each of the hub's ports. The total charging current (divided into all ports) reaches up to 2.8A at 5V (depending on the capabilities of the computer's USB port).

Entry:

• 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-C male.
• Backwards compatible with USB 3.1 Gen 1 / USB 3.0 and USB 2.0.
• Compatible with Thunderbolt 3.
• USB connection port with type C (male) connector placed on a 20 cm long cable.

USB output:

• 2x SuperSpeed USB port, USB-A female connector.
• 1x USB-C Power Delivery port (for charging only), USB-C female connector.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A in each of the hub's ports. The total charging current (which is divided into ports) reaches up to 2.5A at 5V (depending on the capabilities of the external wall charger).

HDMI out:

• HDMI.
• HDMI A (F) female connector.
• Maximum supported resolution 4K / 4096 x 2160 @ 30Hz.
• Resolution WQHD 2560 x 1440 @ 60Hz max.
• Full HD resolution 1920 x 1080 at 60, 100, 120 Hz max.
• A USB-C port with DisplayPort Alternate Mode (DP Alt Mode) support or a USB-C port with Thunderbolt 3 support is required for proper video output support. We also require a suitable operating system. The video output function will not be available when these requirements are not met.
• Hot-Plug-Detect support.
• TMDS (Transition Minimized Differential Signaling) support.
• Full support for HDCP 1.4 and 2.3 (High-bandwidth Digital Content Protection).
• Audio up to eight LPCM channels, support for audio compression (AC-3, DTC) and HBR audio.
• Sampling rate up to 192kHz and 24-bit audio support - depends on source and destination devices, e.g. notebook/phone and TV/display/AV receiver.

Card reader - two slots:

• Micro SD slot: microSD / microSDHC / microSDXC / TransFlash,
• SD slot: SecureDigital / SDHC / SDXC, MultiMedia Card, MMC 4.0, MMC Dual Voltage, MMC mobile, RS-MMC, with adapter - miniSD, microSD / microSDHC / microSDXC, MMC Micro.

The reader supports the following flash card specifications:

• SD 1.0/1.1 (SD - Secure Digital, up to 2GB).
• SD 2.0 (SDHC - Secure Digital High Capacity, up to 32GB).
• SD 3.0 (SDXC - Secure Digital eXtended Capacity, up to 2TB).
• MMC and eMMC 3.x /4.0 / 4.1 / 4.2 / 4.3 / 4.4 / 4.5 / 5.0 (8-bit).
• Support SD 3.01 and SD Jukebox APP (CPRM function).
• Support Ultra High Speed bus UHS-I (SDR12/SDR25/SDR50/DDR50/SDR104) up to 104 MB/s.
• Support for ECC (Error Correction Code) and CRC (Cyclic Redundancy Check) hardware functions.
• 2 LUN - in file managers the reader is indicated as two disks.

Power Delivery:

• Power Delivery 3.0 support - continuous power supply to the device from the network adapter via the USB-C hub.
• Maximum power supply via PD output USB-C hub 100W - 20V/5A.
• Notebook or phone with Power Delivery support from USB-C port and appropriate network PD adapter required.

Entry:

• 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-C male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• Compatible with Thunderbolt 3 interface.
• USB connection port with a type C male connector placed on a 20 cm long cable.

Exit:

• 4x SuperSpeed USB port, USB-A female csatlakozó.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.

Characteristics

• Possibility to connect the device on the run thanks to Hot Plug support.
• Full Plug and Play support.
• Standby mode support.
• A quality shielded cable guarantees high communication speed and minimal unwanted interference.
• The white LED indicates connection to the computer's USB port.
• Bus powered (USB bus power).

Power / Charging:

• USB power is sufficient to connect low-power USB devices (mouse, keyboard, card reader, flash drive, etc.) or self-powered devices (printer, scanner, 3.5" external drive) to all four ports.
• The USB hub can permanently support several external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A is possible in each of the hub's ports. The total charging current (divided into all ports) reaches up to 2.8A at 5V (depending on the capabilities of the computer's USB port).

Entry:

• 1x USB 3.2 Gen 2 / SuperSpeed USB 10 Gbps port, USB-C male.
• Backward compatible with USB 3.2 Gen 1 / USB 3.1 Gen 1 / USB 3.0 and USB 2.0.
• Compatible with Thunderbolt 3.
• USB connection port with type C (male) connector placed on a 13 cm long cable.

USB output:

• 2x SuperSpeed USB 10 Gbps port, USB-A female connector.
• 1x SuperSpeed USB 10 Gbps port, USB-C female connector.
• 1x SuperSpeed USB 10 Gbps port for data transfer or Power Delivery, USB-C female connector.
• Support 10,000 / 5,000 / 480 / 12 / 1.5 Mbps (SuperSpeed+ / SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 2 interface used (theoretically up to 10 Gbit / s).
• The USB-C hub can permanently support several external drives.
• Fast charging of mobile devices through the USB-C hub ports with a current of up to 3A.

HDMI out:

• HDMI.
• HDMI A (F) female connector.
• Maximum supported resolution 4K / 4096 x 2160 @ 30Hz.
• A USB-C port with DisplayPort Alternate Mode (DP Alt Mode) support or a USB-C port with Thunderbolt 3 support is required for proper video output support. We also require a suitable operating system. The video output function will not be available when these requirements are not met.
• Hot-Plug-Detect support.
• TMDS (Transition Minimized Differential Signaling) support.
• Full support for HDCP 1.4 and 2.3 (High-bandwidth Digital Content Protection).
• Audio up to eight LPCM channels, support for audio compression (AC-3, DTC) and HBR audio.
• Sampling rate up to 192kHz and 24-bit audio support - depends on source and destination devices, e.g. notebook/phone and TV/display/AV receiver.

Power Delivery:

• Power Delivery 3.0 support - continuous power supply to the device from the PD network adapter via the USB-C hub.
• Maximum power supply via PD USB-C output 60W - 20V/3A.
• Notebook or phone with Power Delivery support from USB-C port and appropriate network PD adapter required.

Entry:

• PCI-Express 2.1 interface, compatible with PCI-Express 1.0a/1.1. / 2.0 / 3.0
• Number of lanes 1-Lane (x1), compatible with x1 / x4 / x8 / x16 PCIe slots
• 1-Lane PCI-Express 2.1 5Gb/s bus throughput

Exit:

• Gigabit Ethernet interface with RJ-45 connector for connection via UTP or STP cable
• Supported Ethernet interface baud rates 10/100/1000/2500 Mb/s
• Supported specification IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3bz 2.5GBase-T

Hub power via USB cable (bus power):

• USB charging is sufficient to connect a low-power USB device (mouse, keyboard, card reader, flash drive, etc.) or self-powered (printer, scanner, 3.5" external drive) to all four ports.
• In this power mode, the USB hub can handle up to 2 magnetic 2.5" external drives at the same time.
• Powering portable devices (including iPad) is possible in this power mode, but the power supply current reaches only 0.9A, in some cases even over 1A (depending on the computer).

Powering your own hub from a USB charger - not included in the package (self power):

• You can use any mobile device charger with a micro USB connector (recommended charger output current 2A).
• The USB hub in this power mode can handle 3 magnetic 2.5 external drives. However, for reliable long-term operation of the hub, we recommend connecting a maximum of 2 external 2.5" drives at the same time.
• Fast charging of mobile devices (including iPad) with up to 2A current in each of the hub's ports. The total current delivered by the hub while charging is limited by the output current of the external power adapter.

Standalone power hub mode without PC connection (charging hub):

• When the computer is turned off, connected or not connected to the computer, the hub works with power from the USB charger as a standalone USB power hub.
• Fast charging of mobile devices (including iPad) with up to 2A current in each of the hub's ports. The total current delivered by the hub while charging is limited by the output current of the external power adapter.

Input:

• 1x USB 3.2 Gen1 / SuperSpeed USB port, USB-A male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0 and USB 1.1.
• USB connection port with type A male connector placed on a 20 cm long cable.

Output:

• 4x SuperSpeed USB port, USB-A female connector.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.

Characteristics:

• Possibility to connect the device on the run thanks to Hot Plug support.
• Full Plug and Play support.
• Standby mode support.
• A quality shielded cable guarantees high communication speed and minimal unwanted interference.
• A white LED indicates that the hub is connected to the computer.
• Bus powered (USB bus power).

Power / Charging:

• USB power is sufficient to connect low-power USB devices (mouse, keyboard, card reader, flash drive, etc.) or self-powered devices (printer, scanner, 3.5" external drive) to all four ports.
• The USB hub can permanently support several external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A is possible in each of the hub's ports. The total charging current (divided into all ports) reaches up to 2.8A at 5V (depending on the capabilities of the computer's USB port).

Input:

• 1x USB 3.2 Gen1 / SuperSpeed USB port, USB-C male connector.
• Backwards compatible with USB 3.1 Gen 1 / USB 3.0 / USB 2.0.
• Compatible with Thunderbolt 3.
• USB connection port with a type C male connector placed on a 20 cm long cable.

USB output:

• 3x SuperSpeed USB port, USB-A female connector.
• 1x USB Type-C Power Delivery connector (charging only), USB-C female.
• Support 5.000 / 480 / 12 / 1.5 Mbps (SuperSpeed / High / Full / Low speed).
• The overall permeability / transmission speed of the housing is given by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit / s).
• The USB-C hub can permanently support several external drives.
• Charging mobile devices (including iPad) with a current of up to 1.5A is possible in each of the hub's ports. The total charging current (divided into all ports) reaches up to 2.1A at 5V (depending on the capabilities of the computer's USB port).

HDMI out:

• HDMI.
• HDMI A (F) female connector.
• Maximum supported resolution 4K / 4096 x 2160 @ 30Hz.
• Resolution WQHD 2560 x 1440 @ 60Hz max.
• Full HD resolution 1920 x 1080 at 60, 100, 120 Hz max.
• USB-C with DisplayPort Alternate Mode (DP Alt Mode) or USB-C with Thunderbolt 3 support is required for proper video output. At the same time, support from the device (laptop, phone) and operating system is necessary. The video output function will not be available when these requirements are not met.
• Hot-Plug-Detect support.
• TMDS (Transition Minimized Differential Signaling) support.
• Full support for HDCP 1.4 and 2.3 (High-bandwidth Digital Content Protection).
• Audio up to eight LPCM channels, support for audio compression (AC-3, DTC) and HBR audio.
• Sampling rate up to 192kHz and 24-bit audio support - depends on source and destination devices, e.g. notebook/phone and TV/display/AV receiver.

RJ-45 Output:

• Gigabit Ethernet interface with RJ-45 connector for connection via UTP or STP cable.
• Support 10/100/1000Mbps Ethernet interface baud rate.
• Support specification IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T.
• 10/100/1000 Mbit/s auto-sensing.
• Support IPv4/IPv6 packet Checksum Offload Engine (COE) to lower CPU load including IPv4 IP/TCP/UDP/ICMP/IGMP & IPv6 TCP/UDP/ICMPv6 checksum and checksum generation.
• Support TCP Large Send Offload V1 and V2.
• Support IEEE 802.1P Layer 2 priority encoding & decoding.
• Support IEEE 802.1Q VLAN tagging.
• IEEE 802.3az EEE (Energy Efficient Ethernet) support - reduce idle power consumption.
• Jumbo frame support.
• It supports full duplex transmission with IEEE 802.3x flow control and half duplex transmission with reverse flow control.
• Auto MDI/MDIX support - crossover detection and autocorrection eliminates the need for crossover cables.
• Hardware Cyclic Redundancy Check (CRC) support for detecting transmission errors.
• Support Pair Swap/Polarity/Skew Correction.
• Multi-mode Wake-on-LAN support Sleep and remote wake-up support with Magic packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection, ECMA-393 proxZzzy for sleeping hosts, RealWoW! and Link Change wake-up.
• Advanced Power Management Features: The adapter supports advanced power management to reduce power loss in idle or low network traffic. It also supports advanced power saving when disconnecting from the Ethernet cable. It also supports advanced power saving when disconnecting from the Ethernet cable. Advanced Configuration Power management Interface (ACPI), Link Power Management (LPM) or IEEE 802.3az EEE (Energy Efficient Ethernet) support.

Power Delivery:

• Power Delivery 3.0 support - continuous power supply to the device from the PD network adapter via the USB-C hub.
• Maximum power supply via PD USB-C output 60W - 20V/3A.
• Notebook or phone with Power Delivery support from USB-C port and appropriate network PD adapter required.

Input:

• 1x USB 3.2 Gen 2 / SuperSpeed USB 10 Gbps port, with USB-C male connector.
• Backward compatible with USB 3.2 Gen 1 / USB 3.1 Gen 1 / USB 3.0 and USB 2.0.
• Compatible with Thunderbolt 3.
• USB type C male connection connector placed on a 13 cm long permanently attached cable.

USB output:

• 2x SuperSpeed USB 10 Gbps port, USB-A female connector.
• 2x SuperSpeed USB 10 Gbps port, USB-C female connector.
• Support 10,000 / 5,000 / 480 / 12 / 1.5 Mbps (SuperSpeed+ / SuperSpeed / High / Full / Low speed).
• The overall throughput/transmission rate of the station is given by using the USB 3.2 Gen 2 interface (theoretically 10 Gbit/s).
• The USB-C hub can permanently support several external drives.
• Fast charging of mobile devices via USB-C ports with a current of up to 3A at 5V.

Input:

• USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB 5 Gbps.
• Speeds of up to 5 Gbit/s.
• Connection via USB-B female connector.

Device support:

• SATA III interface - 6 Gb/s (600 MB/s),
• 2.5" SSD/HDD support,
• 3.5" HDD,
• maximum drive capacity all unrestricted,
• maximum 2.5" drive height all unlimited.

Power supply:

• Power supply via compact external AC/DC 12V - 2.5A (30W) adapter with 150 cm cable length.
• Power switch.

Disk cloning function:

• Cloning takes place without connecting the station to the computer.
• The target disk must have the same or greater capacity than the source disk, otherwise cloning cannot be activated.
• Both HDD and SSD drives can be cloned.
• Cloning is initiated by pressing the CLONE button and holding it for at least 3 seconds.
• 4 LED indicating the cloning process and completion of cloning.
• SSD cloning speed up to 300 MB/s.
• Total disk cloning time depends on the capacity of the source disk, not on the amount of data on the disk.

Input:

• USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB 5 Gbps.
• Speeds of up to 5 Gbit/s.
• Connection via female USB Micro-B connector.

Device support:

• SATA III interface - 6 Gbps (600 MB/s).
• Support of 2.5" SSD/HDD.
• Maximum drive capacity all without restriction.
• Maximum 2.5" drive height all unlimited.

Features:

• Compatible with USB 3.2 Gen 2, (USB 3.1 Gen 2),USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0), backward compatible with USB 2.0.
• Supports transmission speeds of 5000 / 480 Mbit/s (SuperSpeed / HighSpeed).
• Compatible with Serial ATA 3.0 (SATA/600) specification, transmission speeds up to 6 Gb/s (600 MB/s).
• Compatible with Serial ATA 2.0 (SATA/300) specification, transmission rates up to 3 Gb/s (300 MB/s).
• Compatible with Serial ATA 1.0 (SATA/150) specification, transmission rates up to 1.5 Gb/s (150 MB/s).
• Compliant with USB Mass Storage Class specification.
• The overall transfer rate / baud rate of the station is given by the use of the USB interface (theor. 5 Gbit/s).
• Support of BOT (Bulk-Only Transport).
• UASP (USB Attached SCSI) support for faster data transfer in Windows 8 and later.
• Support for TRIM function to reduce slow SSD performance degradation over time.
• Support for S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology), which monitors drive health.
• Support for booting from the SSD/HDD in the docking station.
• Ability to connect the device behind the gear thanks to Hot Plug support.
• Full Plug and Play support.
• HDD Auto Spindown - automatically sleeps the drive when idle.
• HDD Turn Off - turns off the drive when the device is picked up or the PC goes to sleep.   
• Connection via USB Micro-B female connector.
• USB Micro-B USB-A cable 60 cm long included in the package.
• LEDs to indicate SSD/HDD dock power and drive activity in both docks.

Input:

• USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB with speeds of up to 5 Gbit/s.
• Connection via micro USB type B female connector.

Device support:

• SATA III interface - 6 Gb/s (600 MB/s),   
• support of 2.5" HDD/SSD,
• 3.5" HDD,
• Maximum drive capacity all unrestricted,
• Maximum drive height 2.5" all without restriction.

Card reader:

• five-slot reader supporting the following formats:
• Micro SD slot: microSD / microSDHC / microSDXC / TransFlash,
• SD slot: SecureDigital, SDHC, SDXC, MultiMedia Card, MMC 4.0, MMC Dual Voltage, MMC mobile, RS-MMC, with miniSD, miniSDHC, MMC Micro adapter,
• MS slot: Memory Stick, MS Pro, MS Duo, MS Magic Gate, MS Pro Duo Magic Gate, Memory Stick Pro HG Duo, with M2 adapter (MS Micro),
• CF slot: CompactFlash Type I, CF Type II, CF Extreme III, CF Ultra II, Microdrive, Magicstor,
• XD slot: xD Picture Card, xD Type M, xD Type M+, xD Type H, SmartMedia cards are not supported.

Flash card specification support:  

• SD 1.0/1.1 (SD - Secure Digital, up to2GB),
• SD 2.0 (SDHC - Secure Digital High Capacity, up to 32GB),
• SD 3.0 (SDXC - Secure Digital eXtended Capacity, up to 2TB),
• MMC 3.x/4.0/4.1/4.2/4.3/4.4 (8-bit),
• MS 1.43, MS Pro 1.05, MS Pro HG 1.03, MS-XC 1.0 (up to 2TB),
• CF 5.0 (UDMA 0 - UDMA 6),
• xD 1.2.
• CF Car support in case of PIO mode 6 and Ultra DMA mode.
• Support of SD3.0 UHS50 (SDR50/DDR50 mode) and SD Jukebox application (CPRM function).
• Support for MSXC Power Class 0, 1 and 2.
• Support for Memory Stick Pro MagicGate function and Memory Stick Pro MS Formatter function.
• Support of ECC (Error Correction Code) and CRC (Cyclic Redundancy Check) hardware functions.
• 1 LUN - in file managers, the reader is indexed as one new mechanic - no need to search for active units with an inserted card.
• Supports FAT 12/16/32/64, NTFS, exFAT (FAT 64) file formats.

• 4 downstream USB 3.0 ports with enough space around the connectors.
• upstream USB 3.0 port with USB 3.0 type-A male connector on permanently attached 120 cm long cable.
• Compatible with USB 3.0, backwards compatible with USB 2.0 and USB 1.1.
• Support 1.5 / 12 / 480 / 5000 Mbit/s (low / full / high / super speed).
• USB Battery Charging support in specification 1.2.
• Charging source with USB type-A 5V/2A output and micro USB charging & data cable 1.5 m included in the package.
• Each port of the hub can be used to charge up to 2 A (with an external USB charger connected).
• Supports iPad charging up to 2A (with external USB charger), up to 1A (without external charging).
• Possibility to connect the device on the run thanks to Hot Plug support.
• Total Plug and Play support.
• LED indicating that the hub is connected to power.
• Overcurrent detection and protection.

• 4 downstream USB 3.0 ports with enough space around the connectors.
• upstream USB 3.1 Gen 1 port with a USB type-C male connector on a permanently attached 40 cm long cable.
• Compatible with USB 3.1 gen 1 / USB 3.0, backwards compatible with USB 2.0 and USB 1.1.
• Support 1.5 / 12 / 480 / 5000 Mbit/s (low / full / high / super speed).
• USB Battery Charging support in specification 1.2.
• Each port of the hub can be used for charging up to 2A (with an external USB charger - not part of the package).
• Possibility to connect the device on the run thanks to Hot Plug support.
• Total Plug and Play support.
• LED indicating that the hub is connected to power.
• Overcurrent detection and protection.

• Full Plug and Play support.
• Support for M.2 drives of all sizes - 2230, 2242, 2260, 2280, 22110 mm.
• Support for M.2 drives of all capacities.
• Use both drives simultaneously.
• Support single-sided and double-sided M.2 drives.
• Better heat dissipation from M.2 SSDs thanks to copper vents.
• Support booting from SSD card.

ATTENTION! In the adapter, you can insert B+M-key disks into both M.2 slots. It is important to check the disk parameters - i.e. whether the disk is designed for the SATA or NVMe (PCI-Express) interface and connect it to the correct slot. SATA drives are connected to the B-key slot, NVMe drives are connected to the M-key slot.

Input:

• PCI-Express interface, compatible PCI-Express version: 4.0 / 3.0 / 2.1 / 2.0 / 1.1 / 1.0a.
• Number of lanes 4-Lane, compatible with x4 / x8 / x16 PCIe slots.
• SATA connector for connecting to the motherboard when using a SATA M.2 SSD. In order to achieve the best transmission speeds, we recommend using a SATA 6G controller.

Output:

• NGFF 75-pin M-key slot for mounting the NVMe (PCI-Express) M.2 SSD.
• NGFF 75-pin B-key slot for mounting a SATA (AHCI) M.2 SSD.

Power:

• The adapter is powered directly from the PCI-Express bus, external power is not necessary.
• The dual power system gives enough power to the connected M.2 SSDs.
• The redundant power system also reduces the load on the adapter.

• SuperSpeed USB interface - USB 3.2 Gen 1 (previously USB 3.1 Gen 1 / USB 3.0).
• 4 downstream SuperSpeed USB female A ports with enough space around the connectors.
• 1 USB 3.2 Gen 1 upstream port with USB 3.0 type-A male connector on permanently attached 14 cm long cable.
• Compatible with USB 3.2 Gen 2, backwards compatible with USB 2.0 and USB 1.1.
• Support 1.5 / 12 / 480 / 5000 Mbit/s (low / full / high / super speed).
• Hot Plug Connectivity.
• Total Plug and Play support.
• Standby support.
• USB bus power - USB bus power.
• Mobile device power support.
• A quality shielded cable guarantees high communication speed and minimal unwanted interference.

• SuperSpeed USB interface - USB 3.2 Gen 1 (previously USB 3.1 Gen 1 / USB 3.0).
• 4 downstream SuperSpeed USB female A ports with enough space around the connectors.
• 1 USB 3.2 Gen 1 upstream port with USB type-C male connector on permanently attached 14 cm long cable.
• Compatible with USB 3.2 Gen 2, backwards compatible with USB 2.0 and USB 1.1.
• Support 1.5 / 12 / 480 / 5000 Mbit/s (low / full / high / super speed).
• Hot Plug Connectivity.
• Total Plug and Play support.
• Standby support.
• USB bus power - USB bus power.
• Mobile device power support.
• A quality shielded cable guarantees high communication speed and minimal unwanted interference.

• Total Plug and Play support.
• Support for simultaneous operation of SuperSpeed USB, USB 2.0 and USB 1.1 devices.
• Corresponds to the final official specification xHCI revision 1.0 from USB-IF.
• UASP (USB Attached SCSI) support for faster data transfer in Windows 8 and later.
• Fully supports hot plug connection and disconnection of USB devices per run.
• Powering the controller and connected USB peripherals via the PCI-Express bus.

Input:

• PCI-Express 2.0 interface, compatible with PCI-Express 1.0a / 1.1 / 2.1 / 3.0.
• Number of lanes 1-Lane (x1), compatible with x1 / x4 / x8 / x16 PCIe slots.
• 1-Lane PCI-Express 2.0 bus bandwidth up to 5 Gb/s.

Output:

• 2x 19-pin internal USB 3.2 Gen 1 connector with two ports for connecting e.g. internal SuperSpeed USB reader or front USB ports on the computer case.
• SuperSpeed USB interface - USB 3.2 Gen 1 (previously USB 3.1 Gen 1 / USB 3.0).
• Compatible with USB 3.2 Gen 2, backwards compatible with USB 2.0 and USB 1.1.
• Support 5000 / 480 / 12 / 1.5 Mbps (super / high / full / low speed).
• When connected to the PCI-Express bus version 1.0 theor. transmission speed up to 2500 Mb/s.

• Charger
• Multilingual manual
• Cardboard box with a hole for hanging

• Charger
• Multilingual manual
• Packed in a cardboard box with a clearly presented product

• Dual wall charger
• Multilingual manual
• Packed in a cardboard box with a clearly presented product

• PCI-Express Gigabit Ethernet card with standard bracket
• Follow low profile
• Printed installation manual
• Packed in a cardboard box

• PCI-Express adapter with standard peg
• Low profile herring
• 2 pcs of heat conductive pads
• 50 cm SATA data cable
• Mounting material and screwdriver
• Printed installation manual
• Packed in a cardboard box

• PCI-Express controller with standard peg
• Low-profile end cap
• Multilingual manual
• Packed in a cardboard box

• Radiator with a fan and a 38 cm long power cable
• Metal frame
• 3 pcs of heat conductive pads
• Mounting material and screwdriver
• Packed in a cardboard box

• SSD/HDD dock,
• USB Micro-B USB-A cable 60 cm long,
• power cable 100 cm,
• printed installation manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA,
• packed in a cardboard box.

• SSD/HDD docking station
• USB-B USB-A cable, 70 cm in length
• Power adapter 100-240V / 12V-2.5A
• Multilingual manual
• Packed in a cardboard box

• SuperSpeed USB-C hub with 14cm fixed cable
• Installation manual
• Packed in a blister sealed on both sides with clearly indicated parameters

• SuperSpeed USB-C hub with 20cm fixed cable
• Printed installation guide
• Packed in a cardboard box with a hole for hanging.

• SuperSpeed USB-C multi-hub with 20 cm fixed cable
• Printed installation guide
• Packed in a cardboard box with a hole for hanging

• SuperSpeed USB card reader,
• USB connector cap,
• packed in a cardboard box with a hanging hole.

• SuperSpeed USB card reader,
• multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA,
• packed in a cardboard box with a hanging hole.

• SuperSpeed USB hub with 14cm fixed cable
• Installation manual
• Packed in a blister sealed on both sides with clearly indicated parameters

• SuperSpeed USB hub with 20cm fixed USB cable
• Printed installation guide
• Packed in a cardboard box with a hole for hanging

• SuperSpeed USB hub with 30cm fixed USB cable
• Multilingual manual
• Packed in a cardboard box with a hole for hanging

• SuperSpeed USB hub with 120 cm USB cable permanently
• Printed installation guide
• Packed in a cardboard box with a hole for hanging

• SuperSpeed USB multi port hub with 20 cm fixed USB cable
• Printed installation guide
• Packed in a cardboard box with a hole for hanging

• USB-C 3.1 hub with 40 cm fixed cable
• Printed manual
• Packed in a cardboard box

• USB-C hub with 13 cm cable permanently
• Printed installation manual
• Packed in a cardboard box

• USB-C hub with 20 cm cable permanently
• Printed installation manual
• Packed in a cardboard box with a hole for hanging

• USB-C hub with a 13 cm fixed cable
• Installation manual
• Packed in a cardboard box

• USB 3.0 - SATA adapter with 22 cm fixed cable
• Printed installation guide
• Packed in a cardboard box

• USB 3.0 - SATA adapter with 22 cm long fixed cable
• Power adapter 100-240V / 12V-2A
• Printed installation instructions
• Packed in a cardboard box

• USB 3.0 hub with 16 cm fixed cable
• Packed in a blister sealed on both sides with clearly defined parameters and installation instructions

• USB 3.0 hub with 120 cm fixed cable
• Printed installation manual
• Packed in a cardboard box

• USB 3.0 hub with 120 cm fixed cable
• Universal charging/charging adapter with 5V/2A USB output
• Universal charging and data cable USB type A male / micro USB male length 150 cm
• Printed manual
• Packed in a cardboard box

• USB 3.2 Gen 1 HDD dock
• Micro USB-B - USB-A cable, length 80 cm
• Power adapter 100-240V / 12V-2A
• Installation manual
• Packed in a cardboard box with parameters clearly indicated

• card reader,
• USB cable 10 cm long,
• packed in a double-sided heat sealed blister with the installation guide.

63 × 63 × 15 mm

68 x 21 x 10 mm

70 x 24 x 18 mm

71 x 44.5 x 14.3 mm

75 x 36 x 12 mm

76 x 24 x 12 mm

87 x 40 x 12 mm

89 x 58 x 59 mm

90 x 23 x 13 mm

90 x 45 x 27 mm

96 x 32 x 22 mm

103 x 36 x 32 mm

105 x 40 x 12 mm

110 x 35 x 12.5 mm

110 x 35 x 13 mm

130 x 65 x 59 mm

142 x 102 x 80 mm

diameter 60x18mm

• 64 x 60 x 15 mm

• 70 x 24 x 18mm
• USB cable length 120 cm

• 90 x 23 x 13mm
• USB cable length 20 cm

• 96 x 30 x 10mm
• USB cable length 14 cm

• 96 x 35 x 18mm
• USB cable length 20 cm

• Hub dimensions 96 x 32 x 22 mm
• USB charger dimensions 22 x 36 x 76 mm including plugs